Altronix ACM8CB Installation Instructions Manuale Utente Scaricare il pdf (Pagina 3)

ACM8/CB Sub-Assembly - 3 -

Installation Instructions:

WiringmethodsshallbeinaccordancewiththeNationalElectricalCode/NFPA70/NFPA72/ANSI,andwithalllocal

codes and authorities having jurisdiction. Product is intended for indoor use only and should be installed

by qualified personnel.

1. Refer to Sub Assembly Installation Instruction for mounting Rev. MS042511.

Carefully review:

Typical Application Diagram (pg. 4) Terminal Identification Table (pg. 5)

LED Diagnostics (pg. 5) Hook-up Diagrams (pg. 6)

2. Powersupplyinput:

The units can be powered with one (1) power supply which will provide power for both board operation and

the locking devices or two (2) separate power supplies, one (1) to provide power for the board operation and

the other to provide power for the locking devices and/or access control hardware.

Note: The input power can be 12 to 24 volts DC (.5 amp @ 12 volt, .3 amp @ 24 volt current consumption

with all relays energized).

(a) Single power supply input:

If the unit and the locking devices are to be powered using a single power supply, connect the output

(12 to 24 volts DC) to the terminals marked [- Control +].

(b) Dual power supply inputs (Fig. 1, pg. 4):

 Whentheuseoftwopowersuppliesisdesired,jumpersJ1andJ2(locatedtotheleftofthepower/control

terminals) must be cut. Connect power for the unit to the terminals marked [- Control +] and connect power for the

locking devices to the terminals marked [- Power +].

Note: WhenusingDCpowersuppliespolaritymustbeobserved.WhenusingACpowersuppliespolarity

need not be observed.

Note: For UL compliance the power supplies must be UL Listed for Access Control Systems and accessories.

3. Output options (Fig. 1, pg. 4):

The ACM8 will provide either eight (8) switched power outputs, eight (8) dry form “C” outputs, or

any combination of of both switched power and form “C” outputs, plus eight (8) unswitched auxiliary power outputs.

The ACM8CB will provide eight (8) switched power outputs or eight (8) unswitched auxiliary power outputs.

(a) Switched Power outputs:

Connect the negative (-) input of the device being powered to the terminal marked [COM]. For Fail-Safe operation

connect the positive (+) input of the device being powered to the terminal marked [NC]. For Fail-Secure operation

connect the positive (+) input of the device being powered to the terminal marked [NO].

(b) Form “C” outputs:

 Whenform“C”outputsaredesiredthecorrespondingoutputfuse(1-8)mustberemoved.Connectnegative(-)of 

the power supply directly to the locking device. Connect the positive (+) of the power supply to the terminal marked

[C]. For Fail-Safe operation connect the positive (+) of the device being powered to the terminal marked NC]. For

Fail-Secure operation connect the positive (+) of the device being powered to the terminal marked [NO].

Connect positive (+) input of the device being powered to the terminal marked [C] and the negative (-) of the device

being powered to the terminal marked [COM]. Output can be used to provide power for card readers, keypads etc.

4. Input trigger options (Fig. 1, pg. 4):

(a) Normally Open [NO] input trigger:

Inputs 1-8 are activated by normally open or open collector sink inputs.

 Connectdevices(cardreaders,keypads,requesttoexitbuttonsetc.)toterminalsmarked[IN]and[GND].

(b) Open Collector Sink inputs:

Connect the access control panel open collector sink positive (+) to the terminal marked [IN] and the

 negative(-)totheterminalmarked[GND].

5. Fire Alarm Interface options (Figs. 3 through 7, pg. 6):

A normally closed [NC], normally open [NO] input or polarity reversal input from FACP signaling circuit will

 triggerselectedoutputs.ToenableFACPDisconnectforanoutputopenthecorrespondingswitch[SW1-SW8].

 TodisableFACPdisconnectforanoutputclosethecorrespondingswitch[SW1-SW8].

(a) Normally Open [NO] input:

For non-latching hook-up (Fig. 4, pg. 6). For latching hook-up (Fig. 5, pg. 6).

(b) Normally Closed [NC] input:

For non-latching hook-up (Fig. 6, pg. 6). For latching hook-up (Fig. 7, pg. 6).

1 2 3 4 5 6 7 8

Commenti su questo manuale

Nessun commento

Altronix ACM8CB Installation Instructions Manuale Utente Pagina 3

Commenti su questo manuale

Prodotti e manuali riguardandi Accessori per gli impianti elettrici Altronix ACM8CB Installation Instructions